Home > Kenmore Elite > Kenmore Elite Calypso Error C1

Kenmore Elite Calypso Error C1

To access this part, pull the washer forward and remove the back panel of the control panel. So, once again, I was not satisfied with your answer and as per the terms of the initial service, I am not authorizing any payments and want my deposit refunded to it says on here All Stages Open to Answer so here is what it says for the error code you have "CA" "Cl" Average current limit Or Instantaneous current limit If Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! navigate here

Thought maybe this would fix the problem.......I guessed wrong, so i ran the diagnostics and the 99 second count down got down to like 95 seconds and C1 popped up. Back To Top PM Quote Reply Posted: Sun Dec 18th, 2005 05:02 am PM Quote Reply 16th Post Samurai Appliance Repair Man Fermented Grand Master of Appliantology Joined:Mon Mar Call our Parts Department now! 877-803-7957 Back To Top PM Quote Reply Posted: Wed Dec 28th, 2005 11:45 am PM Quote Reply 19th Post Jimbo.2 Grasshopper Joined:Sat Oct 15th, I installed the replacement new motor and the washer has functioned normally for a couple of weeks now, therefore, I’m declaring it fixed. (Fixed for now at least since it is

Our kenmore eliete washer is now stopping when it tries to spin with a c1 error code. this is what the book says Average Current Limit or Instantaneous Current Limit If a status signal comes back from the motor controller that a current limit has been breached, the The small green square=personal message.

The letter sends me email.I love fan letters! Include an image. Possible causes for these two errors are: the drive motor, thermal protector, motor controller or overloading. The Calypso manual was written for the Whirlpool version of this machine not the Sears Kenmore version which I have.

It starts and then stops with a C1 error flashing. The only difference I could detect was the Whirlpool version has an overfill pressure switch the Kenmore version does not. I attached the link below, I hope this helps!!!!! Each is tripped by a signal from the motor controller that a current limit to the drive motor has been exceeded.

Page: 1 2 New Topic Reply Printer Friendly Calypso washer CI CL CA Error Codes Rating: Rate This Topic Excellent Good Fair Poor Horrible AuthorPost Posted: Tue Oct 18th, Posted on Jun 13, 2009 Helpful 6 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a press cancel.. Does anyone have any suggestions on how to proceed?

characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 51 3772939 Register Help Remember Me? ft. MVP: An expert that got 5 achievements. Top Load Washer - White See Details Kenmore 22532 3.5 cu.

Will the evil Calypso win! check over here by Fred M Earned 109,869 community points in Click'>Kenmore September 16th, 2010 Answered in 23 hours Comment 0 votes Didn't find what you are looking for? I found a question in Manage My Life under the Answers button that is similar to the one you asked. How would I check the thermal protector?

ft. I then placed the washer back in service it functioned normally for several loads (before it was consistently failing with the CI code) before again failing with a CI error code. OB - out of balance - indicates of course a load that is not balanced, or is too heavy. his comment is here Help this question get an answer by entering the correct category or product below.

The machine control board may have a bad relay and may need to be replaced. Some models won't be much more expensive than repairing this washer. You can reply with any additional details for further assistance. The images below will help with this. The ice 10/19/2016 10/19/2016 JACUSTOMER-b2yaxe65- Bosch Maxx Classic Wont spin and will only allow first lot 10/19/2016 10/19/2016 JACUSTOMER-x0uwnnmp- LED lighflashing in freezer and fridge, whirpool 10/19/2016 10/19/2016 smitty1486, JACUSTOMER-b2yaxe65- WHICH

Oh exalted one, be patient with we while I post the background explaining this error code and the steps I’ve taken to solve the problem.

The drive motor must be hooked up properly or a “CE” error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. Customer: replied7 years ago. Much to my surprise I found no information on it or its brethren the dreaded CA error. I have a aeg washer with c1 error after prob 50percent of wash done what could this be???

Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Stop sending me e-mails. A Soil Level light for each dispenser will be lit while the valve is actuated. weblink Calypso GVW9959K Top Load Washer...

problem with the motor controller, thermos protector or Motor ... Follow ApplianceAssistant on Twitter! This question will give you some good detailed suggestions, while your waiting on an expert answer. Also, the stand pipe the washer drains into is only 36” high not the recommended minimum height of 39”.

Get more answers from the people in your networks Tags Kenmore , Washers Click to remove this tagging. I went to the manual and got your above answer already. I am not satisfied with this response. Unfortunately, there was no improvement.

i have seen this phenomenon about 6 times and in each case,replacement of the lower harness(part number is on tech sheet) solved the issue- chances are good you could dissect and LOL Blaiser Technician Member Since: Jun 2011 Posts: 447 Country: Re: Whirlpool Calypso Washer C1 Error Code « Reply #8 on: October 19, 2011, 06:58:10 PM » Flipped it over removed