Home > Error Code > Chrysler Error Codes

Chrysler Error Codes

Contents

By the way the post below by "carsqwerty" is consistent with whatweI saw on some tightly bound wiring as we were working to solve this problem. See why it earned our Editors' Choice award. So far it is completly apart and we have found a few things that are definetly causing some of these issues. P0362 Ignition Coil L Primary/Secondary Circuit Peak primary circuit current not achieved with maximum dwell time (high impedance). Check This Out

It allows the various modules (computers) on the vehicle to communicate with each other and share information. Be sure to cycle the ignition key every once in a while during testing. Ask A Mechanic Over 10,000 questions answered! MIL Request Circuit P1705 P/N Signal Output Circuit P1719 - Skip Shift Solenoid CircuitP1740 Torque Reduction Signal Circuit: Overdrive and TCC Solenoid RationalityAl Steier wrote that P1740 is a Chrysler-only code.

Chrysler Error Codes

window module by outtahouston / February 27, 2011 8:00 AM PST In reply to: Grand Cherokee 2000 Electrical Problems Thanks very much for your info. P0749 Pressure Control Solenoid A Intermittent P0750 Shift Solenoid circuit. I will keep posting and would love feedback on any of this. P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor) P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) P0328 Knock Sensor 1 Circuit High

P0108 (M) Manifold Absolute Pressure/Barometric Pressure Circuit High Input MAP sensor input above maximum acceptable voltage. P0519 Idle Speed Performance A rationality error has been detected for target RPM not met during drive idle condition. MIL is displayed as an engine icon on the instrument cluster. (G) Generator Lamp Illuminated Chrysler uses ISO 9142-2 OBDII Communications Protocol Scan Code DRB Scan Tool Display Description of Diagnostic Chrysler 300 Trouble Codes The output speed sensor may need to be replaced.

I decide just to check on the off chance the reboot fixed the issue and low and behold when I hit the key it was 75 degrees outside .... The data provided by the OBD-II system can sometimes pinpoint the specific component that has malfunctioned, saving substantial service time and cost. Also on more weird thing, sometime if your parked and put it in drive and hold the brake it will shake,IF YOU PUT IT IN REVERSE IT WILL BE FINE. We disconnected the negative terminal form the battery for about 2 minutes reconnected and everything works fine, so far.

CarGurus | My account Saved searches Saved listings Saved promotions Sign in Join | Advertise | United States Canada United Kingdom Used Cars New Cars Car Values Sell My Car Jeep Wrangler Error Codes Hope this helps. Sens. This leak source is considered to be internal because any escaping emissions enter into the engine system and not directly into the atmosphere, unlike an external leak.

Dodge Trouble Codes

get some crest and some paper towels or a scotch brite pad... so now it runs and does not overheat , but does not run right. Chrysler Error Codes P0729-P0736 These codes all report problems with the gear ratio. Chrysler Error Code P1684 P0421 Warm Up Catalyst Efficiency Below Threshold (Bank 1) P0422 Main Catalyst Efficiency Below Threshold (Bank 1) P0423 Heated Catalyst Efficiency Below Threshold (Bank 1) P0424 Heated Catalyst

Circuit LowP1193 - Inlet Air Temp. http://canondrivebh.com/error-code/network-error-codes.html It is a 2002 Chevrolet tracker ZR2 2.5 v6. P0156 (M) O2 Sensor Circuit Malfunction (Bank 2 Sensor2) Oxygen sensor heater element malfunction. Source: Dakota Forums Other PCM / ECM Codes: P0602, P0603, P0604, P0605, P0606, P0607, P0608, P0609, P0610. Jeep Diagnostic Codes

I hope that my experience with this helps someone else having this kind of trouble. Grabbed the rubber protective sleeve and work it loose at the door - it fits over a plate in the connector and can just be lifted with a blunt tool and A bus that is shorted to ground will have a very low resistance, possibly below 10 ohms. http://canondrivebh.com/error-code/jungheinrich-error-codes.html Malfunction Indicator Lamp (MIL) In the Grand Cherokee WJ, the MIL gives an indication to the vehicle operator when the Powertrain Control Module (PCM) has recorded a Diagnostic Trouble Code (DTC)

It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. Jeep Liberty Codes P0499 NVLD Canister Vent Valve Solenoid Circuit High A shorted high condition detected in NVLD solenoid circuit. Scan Code DRB Scan Tool Display Description of Diagnostic Trouble Code P0500 (M) PLEASE HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

P0157 (M) O2 Sensor Circuit Low Voltage (Bank 2 Sensor 2) Oxygen sensor input voltage maintained below normal operating range.

P0162 (M) O2 Sensor Circuit Malfunction (Bank 2 Sensor 3) Oxygen sensor heater element malfunction. P0462 (M) Fuel Level Sending Unit Volts Too Low Open circuit between PCM and fuel gauge sending unit. THANKS VERY MUCH FOR YOUR INFO.I am having an issue with the keyless remote not working, but that's nothing over the anxiety of driving with that electrical issue. P1d83 Jeep P0355 (M) Ignition Coil E Primary/Secondary Circuit Peak primary circuit current not achieved with maximum dwell time (High Impedance).

only). Retrieving codes: Turn the ignition key until the digital odometer displays, repeat three times in succession and then back to "On" (On/Off, On/Off, On/Off, On). P0646 A/C Clutch Relay Control Circuit Low P0647 A/C Clutch Relay Control Circuit High P0648 Immobiliser Lamp Control Circuit (Immobiliser pending SAE J1930 approval) P0649 Speed Control Lamp navigate here P0714 Transmission Fluid Temperature Sensor Circuit Intermittent P0715 Input/Turbine Speed Sensor Circuit P0716 Input/Turbine Speed Sensor Circuit Range/Performance P0717 Input/Turbine Speed Sensor Circuit No Signal P0718 Input/Turbine

I get a p303 error code (bad misfire cylinder 3).